Green coal for power - To take care of post-Kyoto issues from energy security point-of-view:

Green coal for power - To take care of post-Kyoto issues from energy security point-of-view: a. Coal is the world’s most abundant and important source of primary energy. Turning a potential pollutant into a clean, green fuel for economical power production has become a matter for concern on a global scale. Coal continues to dominate the energy industries as the single most important and widely-used fuel. Delivering around 27 per cent of the world’s consumption of primary energy, almost half of which is used for electricity generation; reserves of coal are spread worldwide throughout some 100 developed and developing countries, sufficient to meet global needs for the next 250 years. b. Although a combination of economic and environmental pressures has forced the closure of older, inefficient, fossil fuelled thermal stations, the massive growth in power demand on a world scale will continue to be met predominantly by coal-fired plant for the foreseeable future. In many of the rapidly developing and industrializing regions of the world the rate of consumption of coal as a primary fuel for electricity generation is actually increasing. In energy-hungry India alone, coal-burn for power generation is forecast to more than double in the next few years to 350 million tonnes per year. Annual coal production in China, the world’s largest producer, has rocketed to over 1,500 million tonnes. Nevertheless, post-Kyoto issues have heightened environmental awareness, forcing the pace of technological change in the use of this abundant but potentially polluting fuel for power generation. The environmental threat posed by the release of even more millions of tonnes of toxic pollutants, acidic and greenhouse gases from both new and existing coal-burning power stations is widely accepted. Currently, signatories to the Kyoto Protocol are focusing on solutions to the problem of global warming, including the reduction of CO2 and other ‘greenhouse’ gases. In many other non- signatory countries, major programmes have been implemented by utilities and power producers to reduce SOx, NOx and CO2 emissions. Additional environmental concerns have also emerged, including the potential health impacts of trace emissions of mercury and the effects of particulate matter on people with respiratory problems. c. In contrast with both natural gas and LPG, hard coal can contain a wide range of compounds including sulfur in addition to useful hydrocarbons. The percentage of sulfur can vary widely, with relatively low concentrations in the highest quality anthracite and very high amounts in lignite, generating large volumes of SOx. As well as the need to treat the fuel prior to firing and control closely the combustion process itself to limit the production of nitrogen oxides, coal-fired stations based on conventional pulverized coal technology can only reduce SOx emissions through the use of post-combustion treatments. Further problems still remain through the safe disposal of fly ash which can contain high levels of toxic compounds including heavy metals. d. Enormous environmental problems faced by operators of older, coal-fired generating plants all over the world, plants were forced to take drastic action after various public protests about the deadly effects of SOx emissions and other emissions. Emissions from coal and lignite-fired units at various power generating stations caused widespread damage, killing livestock and crops downwind of the plant and causing respiratory illness in the population in many countries. The plants were forced to cut output. This tends to place an unacceptably high strain on the commercial viability of an existing power station in many of the developing nations and represents a completely uneconomic option for the majority of obsolescent installations. Power producers in industrialized developed countries are therefore adopting a variety of leading-edge clean-coal technologies for electricity generation. e. New clean coal technologies are providing an attractive and economically viable option to post-combustion systems. Applying the latest combustion, steam and process technologies in new power plant or upgrading existing coal-fired generating facilities provides significant improvements in thermal efficiency, reducing environmental impact and energy costs to the consumer. At the same time, higher thermal efficiencies result directly in reduced fuel costs, improving profitability and market position for the independent power producer. (i) For new and smaller coal-fuelled generating plant, boilers using well-proven circulating fluidized-bed CFB technology provide a cost-effective and efficient system capable of meeting current and future environmental standards. They are now being widely used and successfully operated in coal-fired generating units, burning a very wide range of coal and other fuels with widely differing heat values and mineral content. These can typically include anthracite, semi-anthracite, bituminous and sub-bituminous coal, lignite and even ‘gob’ – a form of high-ash bituminous coal waste. (ii) As an alternative to direct combustion based systems, coal gasification is becoming increasingly attractive, with Integrated Gasification Combined Cycle (IGCC) technology offering one of the best ‘clean’ options for effective power production. Gasification systems use steam and controlled amounts of air or oxygen under high temperatures and pressures to react with coal to form clean synthetic gas or ‘syngas’. Current systems provide efficient clean-up of the gas-stream to produce a mixture of carbon monoxide and hydrogen which can be used subsequently as a ‘clean’ fuel or a basic feedstock for liquefaction. f. Used as a fuel for power generation in a typical IGCC generating plant, a syngas-fired gas turbine drives a generator, with exhaust heat from the gas turbine recovered to produce steam to power a steam turbine in conventional ‘combined cycle’. IGCC power generating systems are presently being developed and operated in Europe and the US, with commercial systems capable of operating at thermal efficiencies approaching 50 per cent. NOx and Sox emissions levels are minimized with the potential for carbon-capture and sequestration of the CO in the sysngas stream being actively researched as design strategies for near-term and future coal-based IGCC plants. Elemental sulfur is removed from the syngas before combustion and is a highly saleable commercial byproduct. If the gasifier is fed with oxygen rather than air, the flue gas contains highly concentrated CO2 which can readily be captured, at about half the cost of that from conventional plants. g. As an alternative to the direct use of syngas as a fuel for electricity generation, it can also be processed using modern gas-to-liquids (GTL) technologies to produce a wide range of liquid hydrocarbon fuels such as gasoline and diesel oil. Coal-to-oil is a long-established technology in coal-rich South Africa. h. Nevertheless, clean coal technology is moving very rapidly in the direction of coal gasification, with a second stage designed to produce a concentrated and pressurized carbon dioxide stream followed by separation and geological storage. This has the potential to provide extremely low emissions of conventional coal pollutants, and as low-as-engineered carbon dioxide emissions – a vital step in the fight to prevent irreversible climate change.

Coal is Essential for Energy Security for many – Strategies to enlarge supply base and reduce environmental impacts are the prerequisites:

Coal is Essential for Energy Security for many – Strategies to enlarge supply base and reduce environmental impacts are the prerequisites:

A. More and more frequent environmental problems and disasters – floods, forest fires, tornados, air pollution in big cities – cause growing concerns everywhere. Energy harvesting, conversion, production and use contribute to these environmental burdens.

Hence, improving the environmental performance of the energy sector is of paramount importance. Thus, wider application of cleaner fuels and conversion technologies is a key element in the strategy to improve the environmental performance of the energy sector. Further, the lower price of coal as compare to petroleum based fuels; the interest in coal is renewed because of the more even geopolitical distribution of coal reserves and of larger supply bases of coal allover the world.

In fact, the environmental concerns about coal are not associated with coal itself, but with its utilization in different stages of the energy chain. Novel and more environmentally friendly technologies for coal utilization, commonly known as “Clean Coal Technologies” (CCT), are believed to be able to bring coal back into the picture. Hence, CCT recently enjoy a growing interest almost all parts of the world. At present, this interest mostly focuses on cleaner coal conversion through increased efficiency and CO2 capture technologies, for which large R&D efforts are ongoing worldwide.

B. Market implementation of CCT is expected to cause an increase in coal use. Coal demand could also rise significantly because the recent sharp increase in oil prices has a lower impact on coal than on gas prices. This is explained by the more favorable geopolitical distribution of coal reserves compared to that of gas. As a result, coal has become cheaper in relative terms than oil and gas. All in all, in a scenario of soaring oil & gas prices, coal is predicted to be the energy source with the fastest growing demand. The expected increase in coal demand for power generation raises the question of its secure availability in the future. Thus, enlargement of the coal supply base is essential throughout the world, with adoption of cleaner technology.

C. The enlargement of the coal supply base can take place in four main directions:

(a) More powerful mapping techniques for coal reserves - Modern geophysics and seismic techniques, improve mine planning and exploitation by reducing geological uncertainties and increasing extraction efficiencies. At the same time, they can reduce environmental externalities and energy use for coal extraction.

(b) Improvement of existing under-ground mining technologies - Underground (deep) coal mining accounts for about 60% of world coal production. Current best coal recovery rates for underground mining are 50-60% for the “room-and-pillar” technology and about 75% for “longwall” mining. The implementation of modern automated and computerized mining technologies can increase these recovery rates.

(c) Research and development for underground coal gasification - Underground gasification of coal deposits which are not technically or economically exploitable (anymore) with conventional mining technologies, can add enormous coal supply potential in Europe and worldwide. At present underground coal gasification is at an experimental stage. Significant further efforts are necessary to make it technically and economically viable. In many of the countries like India etc., commercialization of underground gasification technologies may reduce the energy import dependence and enhance energy security scenario, apart from creating new employment.

(d) Utilization of coalmine methane (CMM) gas - Methane gas, released from coalmines, has always raised serious safety and environmental concerns. Methane is highly explosive when accumulated in confined areas. It is also a powerful greenhouse gas with 20- times stronger global warming potential than carbon dioxide. On the other hand, CMM, which consists mainly of natural gas, is a suitable clean fuel. The capture and useful utilization of CMM can bring important synergy benefits in terms of enhanced security of supply and better environmental and safety performance of coal mining.

D. Therefore, for realizing the full potential of CCT, coal is sufficiently

(a) Abundant… only if we keep working on the enhancement of coal reserves,

(b) Cheap… as long as the supply continues to match the demand,

(c) Reliable… as long as the supplies are diversified.

To reach market maturity, clean coal technologies, covering extraction, preparation and conversion, need a long term vision and investment security. In the present pre-commercial stage they need firm political commitment and further R&D support.

‘Carbon sequestration’ - Greatest challenge of clean coal technology to deliver "zero emissions" in reality:

‘Carbon sequestration’ - Greatest challenge of clean coal technology to deliver "zero emissions" in reality:

A present trend of clean coal technology is moving rapidly towards a very interesting phase, realizing efficiency improvements of coal. In fact, this clean coal technology together with the use of natural gas and renewables such as wind will not provide the deep cuts in greenhouse gas emissions necessary to meet future national targets. Naturally, a plant to produce hydrogen from coal and sequester emissions will be the world’s zero emission coal-fired plant – as envisaged for ‘FutureGen’ project.

As discussed earlier, the clean coal technology field is moving in the direction of coal gasification with a second stage so as to produce a concentrated and pressurized carbon dioxide stream followed by its separation and geological storage. This technology has the potential to provide what may be called "zero emissions" - in reality, extremely low emissions of the conventional coal pollutants, and as low-as-engineered carbon dioxide emissions.

A. The greatest challenge now is to sequester emissions by carbon capture and geological storage technology. The technology, known as carbon sequestration, has attracted global attention from industries and governments that are eager to capture and bottle up the gas that can linger in the atmosphere for decades.

B. Carbon capture and sequestration begins with the separation and capture of CO₂ from power plant flue gas and other stationary CO₂ sources. At present, this process is costly and energy intensive, accounting for the majority of the cost of sequestration. However, analysis shows the potential for cost reductions of 30–45 percent for CO₂ capture. Post-combustion, pre-combustion, and oxy-combustion capture systems being developed are expected to be capable of capturing more than 90 percent of flue gas CO₂.

C. The primary function of carbon sequestration research and development (R&D) objectives are:

(1) lowering the cost and energy penalty associated with CO₂ capture from large point sources; and

(2) improving the understanding of factors affecting CO₂ storage permanence, capacity, and safety in geologic formations and terrestrial ecosystems.

D. After capturing of carbon the next step is to sequester (store) the CO_2; which has mainly two processes - (i) The primary means for carbon storage are injecting CO₂ into geologic formations or (ii) using terrestrial applications.

(i) Geologic sequestration involves taking the CO₂ that has been captured from power plants and other stationary sources and storing it in deep underground geologic formations in such a way that CO₂ will remain permanently stored. Geologic formations such as oil and gas reservoirs, unmineable coal seams, and underground saline formations are potential options for storing CO₂. Storage in basalt formations and organic rich shales is also being investigated.

(ii) Another form of sequestration is ‘terrestrial sequestration’, which involves the net removal of CO₂ from the atmosphere by plants and microorganisms that use CO₂ in their natural cycles. Terrestrial sequestration requires the development of technologies to quantify with a high degree of precision and reliability the amount of carbon stored in a given ecosystem.

E. Any carbon sequestration program should involve (a) Core R&D, and (b) Demonstration & Deployment.

(a) Core R&D – Core R&D accomplished through laboratory and pilot-scale research, develops new technologies and systems for reducing greenhouse gas emissions from industrial sources. Core R&D integrates basic research and computational sciences to study advanced materials and energy systems. It focuses on few major areas for technology development: (i) CO₂ Capture, (ii) Carbon Storage, (iii) Monitoring, Mitigation, and Verification, (iv) Non-CO₂ Greenhouse Gas Control, and (v) Breakthrough Concepts.

(b) Demonstration & Deployment – It speeds the development of new technologies through commercial opportunities and collaboration with Govt. departments. Core R&D scientists also learn practical lessons from these demonstration projects and are helpful to develop further technology solutions and innovations.

As mentioned above, this system along with use of natural gas and renewable energy sources such as wind, solar etc., will be advantageous in order to mitigate to a great extent in greenhouse gas emissions necessary to meet future national targets. Many countries see "zero emissions" coal technology as a core element of its future energy supply in a carbon-constrained world. They have program to develop and demonstrate the technology and have commercial designs for plants with an electricity cost of only 10% greater than conventional coal plants available by 2012. Australia is very well endowed with carbon dioxide storage sites near major carbon dioxide sources, but as elsewhere, demonstration plants will be needed to gain public acceptance and show that the storage is permanent. In general, "zero emissions" technology seems to have the potential for low avoided cost for greenhouse gas emissions.

‘FutureGen’ project - to design, build and operate a nearly emission-free coal-based electricity and hydrogen:

‘FutureGen’ project - to design, build and operate a nearly emission-free coal-based electricity and hydrogen:

The clean coal technology field is moving very rapidly in the direction of coal gasification with a second stage so as to produce a concentrated and pressurised carbon dioxide stream followed by its separation and geological storage. At present the high cost of carbon capture and storage renders the option uneconomic. But a lot of work is being done by many of the research institutes, to improve the economic viability of this system.

More recently department of energy (DOE) of Federal Govt. of the USA has announced ‘FutureGen’ project to design, build and operate a nearly emission-free coal-based electricity and hydrogen production plant. It will use cutting-edge technologies to generate electricity while capturing and permanently storing carbon dioxide deep beneath the earth. The integration of these technologies is what makes FutureGen unique. Researchers and industry have made great progress advancing technologies for coal gasification, electricity generation, emissions control, carbon dioxide capture and storage, and hydrogen production. But these technologies have yet to be put together and tested at a single plant - an essential step for technical and commercial viability.

Therefore, the FutureGen initiative would have comprised a coal gasification plant with additional water-shift reactor, to produce hydrogen and carbon dioxide. About one million tones of CO₂ would then be separated by membrane technology and sequestered geologically. The hydrogen would have been be burned in a power generating plant and in fuel cells. The project was designed to validate the technical feasibility and economic viability of near-zero emission coal-based generation. Construction of FutureGen was due to start in 2009, for operation in 2012.

Coal gasification processes –

(a) In conventional plants coal, often pulverised, is burned with excess air (to give complete combustion), resulting in very dilute carbon dioxide at the rate of 800 to 1200 g/kWh.

(b) Gasification converts the coal to burnable gas with the maximum amount of potential energy from the coal being in the gas.

(c) In Integrated Gasification Combined Cycle (IGCC) the first gasification step is pyrolysis, from 400°C up, where the coal in the absence of oxygen rapidly gives carbon-rich char and hydrogen-rich volatiles.

(d) In the second step the char is gasified from 700°C up to yield gas, leaving ash. With oxygen feed, the gas is not diluted with nitrogen.

(e) The key reactions today are C + O₂ to CO, and the water gas reaction: C + H₂O (steam) to CO & H₂ - syngas, which reaction is endothermic.

(f) In gasification, including that using oxygen, the O₂ supply is much less than required for full combustion, so as to yield CO and H₂.

(g) The hydrogen has a heat value of 121 MJ/kg - about five times that of the coal, so it is a very energy-dense fuel.

(h) However, the air separation plant to produce oxygen consumes up to 20% of the gross power of the whole IGCC plant system.

(i) This syngas can then be burned in a gas turbine, the exhaust gas from which can then be used to raise steam for a steam turbine, hence the "combined cycle" in IGCC.

(j) To achieve a much fuller clean coal technology in the future, the water-shift reaction will become a key part of the process so that:

(i) C + O₂ gives CO, and

(ii) C + H₂O gives CO & H₂, then the

(iii) CO + H₂O gives CO₂ & H₂ (the water-shift reaction).

(k) The products are then concentrated CO₂ which can be captured, and hydrogen. (There is also some hydrogen from the coal pyrolysis), which is the final fuel for the gas turbine.

(k) Overall thermal efficiency for oxygen-blown coal gasification, including carbon dioxide capture and sequestration, is about 73%.

(l) Using the hydrogen in a gas turbine for electricity generation is efficient, so the overall system has long-term potential to achieve an efficiency of up to 60%.

‘Clean Coal Technology (CCT)’ – methods to remove pollutants from coal.

‘Clean Coal Technology (CCT)’ – methods to remove pollutants from coal.

Carbon dioxide from burning coal is the main focus of attention today, since it is implicated in global warming, and the Kyoto Protocol requires that emissions decline, notwithstanding increasing energy demand.

A. Capture & separation of Carbon dioxide - A number of means exist to capture carbon dioxide from gas streams, but they have not yet been optimised for the scale required in coal-burning power plants. The focus has often been on obtaining pure CO₂ for industrial purposes rather than reducing CO₂ levels in power plant emissions. Capture of carbon dioxide from flue gas streams following combustion in air is expensive as the carbon dioxide concentration is only about 14% at best. This treats carbon dioxide like any other pollutant and as flue gases are passed through an amine solution the CO₂ is absorbed. It can later be released by heating the solution. This amine scrubbing process is also used for taking CO₂ out of natural gas. There is an energy cost involved. Captured carbon dioxide gas can be put to good use, even on a commercial basis, for enhanced oil recovery. Injecting carbon dioxide into deep, unmineable coal seams where it is adsorbed to displace methane (effectively: natural gas) is another potential use or disposal strategy.

B. Coal arriving at a power plant contains mineral content that needs to be removed, in order to make it clean, before it is burnt. A number of processes are available to remove unwanted matter and make the coal burn more efficiently.

(a) Coal cleaning by washing - Coal washing involves grinding the coal into smaller pieces and passing it through a process called gravity separation. One technique involves feeding the coal into barrels containing a fluid that has a density which causes the coal to float, while unwanted material sinks and is removed from the fuel mix. The coal is then pulverised and prepared for burning.

(b) Gasification of coal – The Integrated Gasification Combined Cycle (IGCC) plant is a means of using coal and steam to produce hydrogen and carbon monoxide (CO) which are then burned in a gas turbine with secondary steam turbine (ie combined cycle) to produce electricity.

Coal gasification plants are favoured by some because they are flexible and have high levels of efficiency. The gas can be used to power electricity generators, or it can be used elsewhere, i.e. in transportation or the chemical industry. In Integrated Gasification Combined Cycle (IGCC) systems, coal is not combusted directly but reacts with oxygen and steam to form a "syngas" (primarily hydrogen). After being cleaned, it is burned in a gas turbine to generate electricity and to produce steam to power a steam turbine. Coal gasification plants are seen as a primary component of a zero-emissions system. However, the technology remains unproven on a widespread commercial scale.

(c) Removing pollutants from coal - Burning coal produces a range of pollutants that harm the environment: Sulphur dioxide (acid rain); nitrogen oxides (ground-level ozone) and particulates (affects people's respiratory systems). There are a number of options to reduce these emissions:

(i) Sulphur dioxide (SO2) - Flue gas desulphursation (FGD) systems are used to remove sulphur dioxide. "Wet scrubbers" are the most widespread method and can be up to 99% effective. A mixture of limestone and water is sprayed over the flue gas and this mixture reacts with the SO2 to form gypsum (a calcium sulphate), which is removed and used in the construction industry.

(ii) Nitrogen oxides (NOx) - NOx reduction methods include the use of "low NOx burners". These specially designed burners restrict the amount of oxygen available in the hottest part of the combustion chamber where the coal is burned. This minimises the formation of the gas and requires less post-combustion treatment.

(iii) Particulates emissions - Electrostatic precipitators can remove more than 99% of particulates from the flue gas. The system works by creating an electrical field to create a charge on particles which are then attracted by collection plates. Other removal methods include fabric filters and wet particulate scrubbers.

Clean coal technology (CCT) - A discussion

Clean coal technology (CCT) - A discussion

Coal when burned is the dirtiest of all fossil fuels. A range of technologies are being used and developed to reduce the environmental impact of coal-fired power stations. Thus, clean coal technology (CCT) is the name attributed to coal chemically washed of minerals and impurities, sometimes gasified, burned and the resulting flue gases treated with steam with the purpose of removing sulfur dioxide, and reburned so as to make the carbon dioxide in the flue gas economically recoverable.

A. It is a known fact that, the burning of coal, a fossil fuel, is the principal causes of anthropogenic climate change and global warming. In fact, the byproducts of coal combustion are very hazardous to the environment if not properly contained. This is seen to be the technology's largest challenge, both from the practical and public relations perspectives. While it is possible to remove most of the sulfur dioxide (SO2), nitrogen oxides (NOx) and particulate (PM) emissions from the coal-burning process, carbon dioxide (CO2) emissions will be more difficult to address. Therefore, fact regarding the coal remains:

(a) Coal is a vital fuel in most parts of the world.

(b) Burning coal without adding to global carbon dioxide levels is a major technological challenge which is being addressed.

(c) The most promising "clean coal" technology involves using the coal to make hydrogen from water, then burying the resultant carbon dioxide by-product and burning the hydrogen.

(d) The greatest challenge is bringing the cost of this down sufficiently for "clean coal" to compete with nuclear power on the basis of near-zero emissions for base-load power.

B. In relation to clean coal technology, a terminology ‘carbon capture and storage’ (CCS) is being discussed. CCS is nothing but method of capturing the carbon dioxide, preventing the greenhouse gas entering the atmosphere, and storing it deep underground by various ways, such as

(a) CO2 pumped into disused coal fields displaces methane which can be used as fuel,

(b) CO2 may be pumped into and stored safely in saline aquifers, or

(c) CO2 pumped into oil fields helps maintain pressure, making extraction easier.

A range of approaches of CCS have been developed and have proved to be technically feasible. They have yet to be made available on a large-scale commercial basis because of the costs involved.

C. Clean coal technologies are continually developing. Today, efficiencies of 46% can be achieved by implementing the best available technology. With further research into techniques such as Ultra-supercritical combustion, efficiencies above 50% are envisaged in the near future. Work is underway to exploit the opportunities of capturing and storing CO2, which is an inevitable by-product of the thermal use of all fossil fuels. Coupled with integrated gasification, coal could in this way provide a source of low-carbon hydrogen for fuelling transport without producing local emissions. There will be challenges in bringing these technologies to market, but with the right mix of research investment and market incentives, coal may stake a place in a sustainable and secure energy future.

D. To summarise, burning coal, such as for power generation, gives rise to a variety of wastes which must be controlled or at least accounted for. So-called "clean coal" technologies are a variety of evolving responses to late 20th century environmental concerns, including that of global warming due to carbon dioxide releases to the atmosphere. However, many of the elements have in fact been applied for many years, and they will be only briefly mentioned here:

(i) Coal cleaning by 'washing' has been standard practice in developed countries for some time. It reduces emissions of ash and sulfur dioxide when the coal is burned.

(ii) Electrostatic precipitators and fabric filters can remove 99% of the fly ash from the flue gases - these technologies are in widespread use.

(iii) Flue gas desulfurisation reduces the output of sulfur dioxide to the atmosphere by up to 97%, the task depending on the level of sulfur in the coal and the extent of the reduction. It is widely used where needed in developed countries.

(iv) Low-NOx burners allow coal-fired plants to reduce nitrogen oxide emissions by up to 40%. Coupled with re-burning techniques NOx can be reduced 70% and selective catalytic reduction can clean up 90% of NOx emissions.

(v) Increased efficiency of plant - up to 45% thermal efficiency now (and 50% expected in future) means that newer plants create less emissions per kWh than older ones.

(vi) Advanced technologies such as Integrated Gasification Combined Cycle (IGCC) and Pressurised Fluidised Bed Combustion (PFBC) will enable higher thermal efficiencies still - up to 50% in the future.

(vii) Ultra-clean coal from new processing technologies which reduce ash below 0.25% and sulfur to very low levels mean that pulverised coal might be fed directly into gas turbines with combined cycle and burned at high thermal efficiency.

(viii) Gasification, including underground gasification in situ, uses steam and oxygen to turn the coal into carbon monoxide and hydrogen.

(ix) Sequestration refers to disposal of liquid carbon dioxide, once captured, into deep geological strata.

E. Discussion - Many experts think, the concept of clean coal is said to be a solution to climate change and global warming. Whereas, environmental groups believe it is nothing but another way of making everybody fool, in other words, it is ‘green-wash’. Environmentalists say, with this technology emission and wastes are not avoided, but are transferred from one waste stream to another. They opine that, coal can never be clean. Critics of the planned power plants assert that there is no such thing as "clean coal" and that the plant will still release large amounts of pollutants compared to renewable energy sources such as wind power and solar power. A good deal of investment in research and development and also in implementation of pollutant free renewable energy (such as wind power and solar power) has to augmented, to make the world very clean, to make the required electricity generation fully green.